Pointer types and Arrays

Let us consider why we need to identify the type of variable that a pointer points to, as in:

int *ptr;

One reason for doing this is so that later, once ptr "points to" something, if we write:

*ptr = 2;

the compiler will know how many bytes to copy into that memory location pointed to by ptr. If ptr was declared as pointing to an integer, 2 bytes would be copied, if a long, 4 bytes would be copied. Similarly for floats and doubles the appropriate number will be copied. But, defining the type that the pointer points to permits a number of other interesting ways a compiler can interpret code. For example, consider a block in memory consisting if ten integers in a row. That is, 20 bytes of memory are set aside to hold 10 integers.
Now, let's say we point our integer pointer ptr at the first of these integers. Furthermore lets say that integer is located at memory location 100 (decimal). What happens when we write:

ptr + 1;

Because the compiler "knows" this is a pointer (i.e. its value is an address) and that it points to an integer (its current address, 100, is the address of an integer), it adds 2 to ptr instead of 1, so the pointer "points to" the next integer, at memory location 102.

Similarly, were the ptr declared as a pointer to a long, it would add 4 to it instead of 1.

The same goes for other data types such as floats, doubles, or even user defined data types such as structures. This is obviously not the same kind of "addition" that we normally think of. In C it is referred to as addition using "pointer arithmetic”.

Similarly, since ++ptr and ptr++ are both equivalent to ptr + 1 (though the point in the program when ptr is incremented may be different), incrementing a pointer using the unary ++ operator, either pre- or post-, increments the address it stores by the amount sizeof(type) where "type" is the type of the object pointed to. (i.e. 2 for an integer, 4 for a long, etc.).


Since a block of 10 integers located contiguously in memory is, by definition, an array of
integers, this brings up an interesting relationship between arrays and pointers.


Consider the following:

int my_array[] = {1,23,17,4,-5,100};


Here we have an array containing 6 integers. We refer to each of these integers by means of a subscript to my_array, i.e. using my_array[0] through my_array[5]. But, we could alternatively access them via a pointer as follows:

int *ptr;
ptr = &my_array[0];

And then we could print out our array either using the array notation or by dereferencing
our pointer. The following code illustrates this:

#include<>
int my_array[] = {1,23,17,4,-5,100};
int *ptr;
int main(void)
{
int i;
ptr = &my_array[0]; /* point our pointer to the first
element of the array */
printf("\n\n");
for (i = 0; i < 6; i++)
{
printf("my_array[%d] = %d ",i,my_array[i]); /*<-- A */
printf("ptr + %d = %d\n",i, *(ptr + i)); /*<-- B */
}
return 0;
}


Compile and run the above program and carefully note lines A and B and that the program prints out the same values in either case. Also observe how we dereferenced our pointer in line B, i.e. we first added i to it and then dereferenced the new pointer. Change line B to read:

printf("ptr + %d = %d\n",i, *ptr++);

and run it again... then change it to:

printf("ptr + %d = %d\n",i, *(++ptr));

and try once more. Each time try and predict the outcome and carefully look at the actual
outcome.

In C, the standard states that wherever we might use &var_name[0] we can replace that
with var_name, thus in our code where we wrote:

ptr = &my_array[0];

we can write:

ptr = my_array;

to achieve the same result.

we can write

ptr = my_array;

we cannot write

my_array = ptr;

The reason is that while ptr is a variable, my_array is a constant. That is, the location at
which the first element of my_array will be stored cannot be changed once my_array[]
has been declared.

Now, let's delve a little further into the difference between the names ptr and my_array as used above. Some writers will refer to an array's name as a constant pointer. What do we mean by that? Well, to understand the term "constant" in this sense, let's go back to our definition of the term "variable". When we declare a variable we set aside a spot in memory to hold the value of the appropriate type. Once that is done the name of the variable can be interpreted in one of two ways. When used on the left side of the assignment operator, the compiler interprets it as the memory location to which to move that value resulting from evaluation of the right side of the assignment operator. But, when used on the right side of the assignment operator, the name of a variable is interpreted to mean the contents stored at that memory address set aside to hold the value of that variable.

With that in mind, let's now consider the simplest of constants, as in:

int i, k;

i = 2;

Here, while i is a variable and then occupies space in the data portion of memory, 2 is a constant and, as such, instead of setting aside memory in the data segment, it is imbedded directly in the code segment of memory. That is, while writing something like k = i; tells the compiler to create code which at run time will look at memory location &i to determine the value to be moved to k, code created by i = 2; simply puts the 2 in the code and there is no referencing of the data segment. That is, both k and i are objects, but 2 is not an object.

Similarly, in the above, since my_array is a constant, once the compiler establishes
where the array itself is to be stored, it "knows" the address of my_array[0] and on
seeing:

ptr = my_array;

it simply uses this address as a constant in the code segment and there is no referencing
of the data segment beyond that.

We have learned that on different systems the size of a pointer can vary. As it turns out it is also possible that the size of a pointer can vary depending on the data type of the object to which it points. Thus, as with integers where you can run into trouble attempting to assign a long integer to a variable of type short integer, you can run into trouble attempting to assign the values of pointers of various types to pointer variables of other types.

To minimize this problem, C provides for a pointer of type void. We can declare such a
pointer by writing:

void *vptr;

A void pointer is sort of a generic pointer. For example, while C will not permit the comparison of a pointer to type integer with a pointer to type character, for example, either of these can be compared to a void pointer. Of course, as with other variables, casts can be used to convert from one type of pointer to another under the proper circumstances.